Solvent based fletching glue from Bohning.
Key features:
Designed for securely gluing vanes and feathers.
Appropriate for aluminium, carbon, wood and fiberglass shafts.
Slow curing glue where bond increases over time.
Flexable and durable.
Clamp for 5 minuites and glue cures fully in 48 hours.
Considered by many as the best glue on the market. Suited to glue nocks, feathers and vanes on aluminium, carbon and wooden shafts. Not only is this glue used by many archers that like to make their own arrows, also profesionals like to use this glue. We use the Saunders Arrow Mate Cement for the natural feathers on our custom arrows, it works great and leaves no residue on the shaft when you need to replace a feather.
The Bearpaw dosing tip is extremely fine and precise! It guarantees the best glueing results and helps you put on the right amount of glue. Apart from that, dosing tips have a tendency to get clogged up after use. Therefore, we recommend ordering a few extra dosing tips with the Bearpaw Archery Glue to be ready to replace.Delivery per piece.
This Bearpaw instant glue is specially made without harmful solvents, without compromising on the quality. This way you don’t suffer from harmful and irritating fumes when making arrows. This glue is suited for all materials, so you don’t need a lot of different glues.
Bearpaw instant glue is suited for glueing feathers and vanes on different shafts (wood, carbon, aluminium and fiberglass). And also to glue points and nocks.
The double-sided fletching tape is used worldwide for the swift and durable fletching of wooden, aluminium and carbon arrows. Its extremely simple and quick handling enthuses both archers and bowyers worldwide.
Length: approx. 1830 cm (720 inches)
Quality: Made in Germany
The Avalon Fletching jig is a nice budget option if you want to start making your own arrows. The jig is made from aluminum, making it light and compact, comes with one straight clamp and can fletch 3 or 4 feathers to the shaft.
Hot melt adhesive from Bohning.
Key features:
Optimised for installing arrow points and inserts.
Provides a durable and impact resistant bond.
Suitable for all aluminium and wooden shafts.
Heat reversible bond for adjustment, replacement or removal.
12g stick sufficient for installing approximately 144 inserts.
This white marker of Avalon is extremely useful to provide your arrows with your initials. Everyone will know these arrows are yours!
The thin nib of 0.7 mm ensures that you can work with precision and detail.
Hot melt adhesive from Bohning. A 12gr stick which works at low temperaturs. This prevents you from accidentical overheating your shafts or components.
Key features:
Optimised for installing arrow points and inserts.
Provides a durable and impact resistant bond.
Suitable for all aluminium, carbon and wooden shafts.
Heat reversible bond for adjustment, replacement or removal
The Taper Tool made of plastic is the world’s most widely used tool to attach the cone for tip and nock to wooden arrows. Absolutely simple and reliable in its handling, it convinces archers in their daily use.
Features
Material: PlasticSizes: 5/16, 11/32, 23/64 inches
The Cartel Arrow Fletcher is a light and compact fletching jig made of aluminum. This jig is a nice budget option when you start making your own arrows. The jig gives you the option to fletch 3 or 4 feathers.
AAE Max Bond Glue is specifically formulated for the Arizona Plastifletch Max and Max Hunter vanes. This glue also works well with Elite Plastifletch and most other plastic vanes. Max Bond is a high-viscosity liguid that is easy to work with and penetrates well when using the tough Elastimax material. Whether you are fletching carbon or aluminum, this is the toughest glue available.
Features:
Suited for carbon or aluminum shafts
Works best with vanes
Containes 20gr.
With this tool you can mount parallel screw-on points on wooden shafts. The TopHat® Assembly Tool is suited for arrows of all diameters.
Size: 14 cm x 4 cm
Developed in colleboration with Pfeilgeräte Brand.
With this TopHat®Thread Roughing Tab you can prep shafts for placing a parallel screw-on point. This ensures that the placement of the point goes a lot smoother.
Features
Material: Stainless SteelAvailable sizes: 5/16, 11/32 and 23/64
InstructionsStick the TopHat®Thread Roughing Tab in the TopHat®Assembly Tool and twist it all the way on the shaft, if you have done this you can recplace the tab for the actual point.
The Easton Glue Insert Adhesive is designed especially for inserts. Whether you use carbon or aluminum shafts, this glue works! This glue is desgined to be impact resistant. Bottle contains 15ml.
The Bearpaw Fletching Tool Deluxe is a very accurate fletching jig. The developers of Bearpaw Products were able to combine the experience of Henry Bodnik and the needs of archers. Many individual adjustment options ensure the best and most accurate fletching of your arrows. The basic construction of this functional unit is made of a heavy metal, in order to guarantee both quality and durability. Together with the available base plate, you can easily expand your fletching tool in steps of 3 to a multiple fletching system. You can easily fletch your arrows straight, rightwound or leftwound with our fletching tool.
A masterpiece of German engineering
Features
– Can switch easily from 3- to 4- or 6-fold fletching– Precision holder for thinner and thicker arrow shafts– Centering of the nock– Individual fine tuning for perfect fit of the fletch or feather– Comes with a straight, helical RW or Helical LW clamp
German Quality
Two component epoxy glue is used to glue points on wooden shafts. This glue won’t become super hard but will stay a tiny bit flexible, this will absorb a bit of the impact of the arrow in the target.
The Gas Pro Hot Melt is used for points and inserts with aluminum and wooden shafts. If you want to replace your point all you need to do is heat the point a bit and the glue will become liquid, so you can replace your point without damaging the shaft.
The stick Gas Pro Hot Melt is about 20 cm long.
Perfect compact and lightweight scale to weigh shafts, points, vanes, nocks etc. Very useful tool when you like to make your own arrows.
Features
Total size: 5″ x 3″ x 3/4″ inch
Total weight: 5 oz, with batteries
Capacity: 100g x 0.01g
Batteries: 2 x AAA included
Auto-off power saver mode
Backlit LCD screen
771 grain max with.15 grain accuracy
Measures to the nearest tenth (.1)
Self-contained protective case
With the TopHat Shaft Shaper it is possible to compress your arrow in a responsible way so it has the right diameter for placing a parallel point. Wood might slightly vary in diameter, with this tool you can make the discrepancy dissapear.
Features
Material: Stainless SteelLength: 50mmSizes: 5/16 or 11/32
TopHat®Shaft shaper technology:The TopHat® Shaft- shaper set is composed of ftwo elements. A basepiece can be placed on the drilling machine and the desired attachement can be placed on the basepiece. Put the drilling machine on a slow speed if possible. The shaft has to go into the attachement until it can’t go any further, keep doing this until there is no resistance.
The Replacement Clamps for the Bearpaw Fletching Tool Deluxe is made from a robust and resistant material. They guarantee high functionality and longevity. The clamps are built to precision to ensure a high degree of accuracy in fletching. The form of the wound clips was built in such a way as to be able to press the full surface of the feather quill to the shaft.
Features
Versions: clips rightwound, leftwound and straightGerman Quality
The Decut PCOcut is a great tool to have when you like to make your own arrows. The arrow cutter makes it really easy to cut your carbon, aluminum or wooden shafts to the right size. The cutter works with a foot pedal.
Features
– 220 volt motor speed.
– Spare blade included.
– Quality product at a competitive price point.
With the Cross-X Fletching remover you can remove every vane or feather from your arrow shaft in an instant. You can also easily remove glue residue from loose feathers. Thanks to the round curved blade, this stripper fits nicely around a shaft, allowing the feathers to be removed very effectively.
Archers all over the world use conical points with screw thread for their wooden arrows. At miss-shots arrows often penetrate deeply in branches or timber and can be damaged when pulled. With screw points the arrows can then easily be unscrewed from the tip. With the Arrowpoint Puller it is a breeze to pull the point out of the wood with a sharp tug.
Material: aluminium
Use: for points with conical screw thread in the sizes of 5/16 inches, 11/32 inches, 23/64 inches
Quality: Made in Germany
The ATA (Archery Trade Association) has determined the exact measurements and specifications for taper tools. The amount of angle and the length of the taper to be cut are precisely specified. This ensures that all tips and nocks fit perfectly on your wooden arrows.
Features
Material: AluminiumContents: 3x shaft adapters – 5/16 inches, 11/32 inches, 23/64 inches
Fletching arrows is a time-consuming activity? Not with this Avalon Fletching jig. With 6 straight clamps, a full set of 12 arrows is ready 6 times as fast as before.
Instruction manual included.
With it’s 3 grooved razor sharp-edges, any vane of any shaft is easily removed, as well as any residual adhesive.
Compact and easy to store due to it’s foldable design which also protects the blade.
With the integrated locking mechanism, it is not possible to accidentally close the blade. 4 different sized slots for adjusting a wide variaty of nocks.
Handle made out of aluminum and is available in 3 anodized finishes.
With the Beiter Nockdepot you can easily store your nocks, put it in your bag or hang it on your quiver (through the holes on the side it is possible to attach a ring or string to it). 6 Nocks can be clicked on both sides of the nock depot, so a total of 12 nocks fit on 1 depot.In addition to storage, the nock depot can also be used to install or align your nock on the shaft.Available in 3 models: #1 (black)#2 (orange)hunter (green)
An important tool for the production of your own carbon or aluminum arrows. You increase the adhesion of the insert, if you brush the inside of the carbon or aluminum shafts with this steel brush. This size is suitable for shafts with a diameter of 5/16 and bigger, for smaller diameter shafts we recommend using the Steelbrush Slim.
Features
Diameter: 6 mm (0.24 in)
Material: Steel
Quality: Made in Germany
The Avalon Arrow Inspection Spinner is the ideal tool to check if your arrows are straight. Due to the smooth bearings and solid base, it's easy to see if your shafts, points or pins are completely straight. The spinner is adjustable in length to inspect shorter zones or the arrow and the rubber feet prevent it from slipping.
With the vertical fletching jig by Avalon you can easily create arrows. The fletching jig offers the possibility to make custom arrows according to your own wishes with up to 3 or 4 feathers/vanes per shaft. Despite the fact that this all-rounder is light and compact, the fletching jig offers a lot of stability and regularity in fletching.
Delivery includes: straight clamp and adapter.
The Beiter Push'N'Pull is a handy tool with which you can easily install, turn or exchange both symmetrical and asymmetrical nocks. The ergonomic design allows even the most stuck nocks to be turned or removed without damaging the shaft.Available in 3 models:#1 (Black)#2 (Orange)Hunter (Green)
Bitzenburger Fletching Jig, the best on the market for over 50 years. Used by many professional archers and used by our shop to make custom arrows.
Comes with an Allen Key, instruction manual and a clamp (straight or helical).
Clamps can also be ordered separately
An important tool for the production of arrows with a small diameter, like the Bearpaw Slim Line carbon arrows. You increase the adhesion of the insert or point, if you brush the inside of the carbon or aluminum shafts with our steel brush.
Features
Diameter: 4,5 mm
Material: Steel
Quality: Made in Germany
The Bohning The Strip Pro Vane Stripper is a great tool for removing old vanes and feathers from the shaft. This vane stripper has two ways of use, so you can switch positions while using the stripper, very ergonomical when you have to remove a lot of vanes. The blades last a long time but when they do come to their end you can order replacement blades instead of having to buy a whole new stripper.
Many shooters of wooden arrows still prefer selfnocks sawed directly into the shaft. It is extremely important to saw selfnocks into the shaft in a centered way.
The Self Nocker Plus is a masterpiece of German craftsmanship!
The shaft is centered automatically to perfectly saw the nock into the center of the wooden shaft. The integrated collet chuck clamps wooden shafts of all diameters securely and firmly in the tool.
Features
Material: aluminium with spring steel collet
Use: wooden shafts of diameter 5/16 inches, 11/32 inches, 23/64 inches
Quality: Made in Germany
The Bearpaw Taper Tool Parallel is designed and manufactured according to the specifications of an arrow manufacturer from England. By rotating the milling insert a parallel taper is milled out of the wooden or bamboo shaft. Parallel screw and adhesive tips can be pushed onto the shaft and fit perfectly. The surfaces of the arrow shaft and the tip are almost identical. The Taper Tool Parallel is perfectly adapted to the use of the adhesive tip Bear Point.
Features
Material: Steel
Available versions: 5/16 inches, 11/32 inches, 23/64 inches
Use: wooden shafts, bamboo shafts
Function: parallel milling
Quality: Made in Germany
The Pine Ridge Arrow Inspector helps you check the straghtness of your shafts and alignment of your arrows and components. Also great to use when building wooden arrows to see which side of the shaft you should cut. The inspector is made from high quality plastic, has aluminum wheels for friction free spinning and is easy to dismantle for storage or transport.
Bearpaw Products is making history and revolutionizing arrow spine measuring technology with the Arrow Analyzer!
With the electronic Arrow Analyzer, a unique machines is invented for measuring the deflection (or spine) of arrows and arrow shafts. As a matter of fact, at the world’s largest archery trade show, it was recognized as one of the most impressive archery innovations they had seen in years. They instantly saw the potential of the Arrow Analyzer as a one-tool-does-all device.
Before it has always been difficult to check arrows and to make sure they were actually the spine that the manufacturers claimed. The old spine tester devices were all expensive, large and inconvenient to use. That has all changed thanks to a German developer, who designed and manufactured a machine that could not only check arrow deflection, but also checks arrow straightness and arrow / point weight. Together with Henry Bodnik, a simple machine was produced that is accurate, easy to use, and gives archers all the important information they need. With the Arrow Analyzer, archers can match their arrows perfectly for more accurate and consistent shooting.
The Arrow Analyzer accurately measures:
Arrow spine by the ATA standard or the Easton standard (wooden shafts & carbon)
Arrow mass and point mass weight
Arrow straightness under load and at each end of the arrow to see which end to cut
Features
Stores digital documentation of the measured values in the Arrow Analyzer software
Allows you to export your digital data via the interface to your computer or tablet
Gives you a choice between several exporting formats (Excel, OpenOffice)
Can be used anywhere with an external power source
All software and a user’s guide are included.
Download the manual here
